UF_DRF_align_position_t specifies the site locations in the text box which
can be used to locate a drafting object

suppress zeros for angular dimension only

UF_DRF_angular_format_t specifies the supported formats for angular
display.

These are the valid settings for appended text location

UF_DRF_area_fill_material_t specifies the material to be represented
for area fill

UF_DRF_dimension_extension_line_t specifies whether arrows are to be
displayed on each side of the dimension

Possible value for filled arrowhead

Possible values for arrowhead type

Possible values for combined arrowhead and fill type

The enum value corresponding to 7 is unused since there is no
mapping of the datum symbol.

Line associativity types

object associativity types

The following enumerated type is used to define the type of associative
origin on an annotation.

Drafting block types

Chamfer Dimension : dimension form

Chamfer Dimension : leader type

Chamfer Dimension : stub type

Chamfer Dimension : symbol type

Text types for custom symbols

UF_DRF_decimal_point_character_t specifies the decimal point character,
period or comma

UF_DRF_diameter_radius_placement_t specifies the diameter or radius
symbol placement

UF_DRF_diameter_symbol_t specifies the symbol type for a diameter
dimension symbol

UF_DRF_dimension_orientation_t specifies the alignment of text relative to
the dimension orientation.

Ordinate dimension dog leg display types

UF_DRF_dual_dimension_format_t specifies the supported formats for dual
dimension display.

UF_DRF_dimension_extension_line_t specifies whether extension lines are to
be displayed on each side of the dimension

UF_DRF_fraction_type_t specifies the supported format for dimension text.

frame corner for UF_DRF_leader_type_t = UF_DRF_leader_type_ext_line

id symbol types

enum declarations for the types of feature annotation which can be inherited
Currently only UF_DRF_INHERIT_FEATURE_PARAMETERS is supported

Dimension inspection display option

leader attachment type

leader mode

Possible values for leader orientation:

leader type

UF_DRF_line_width_t specifies the supported line widths

UF_DRF_linear_units_t specifies the supported types of linear units.

The following enumerated type contains those "line types" supported by
annotation associativities.

The following enumerated type contains those "point types" supported by
annotation associativities.

Ordinate dimension arrow and line display types

Ordinate dimension margin types

Ordinate dimension origin name display type

Ordinate dimension positive quadrant

UF_DRF_radius_symbol_t specifies the symbol type for a radial dimension
symbol

Dimension reference display option

UF_DRF_retained_state_t defines the states for retained annotations

UF_DRF_section_line_arrowhead_t specifies the type of arrowhead for
section line display

UF_DRF_section_line_display_t specifies the type of section line display

The following enumerated type describes the type of connections for a custom symbol

Control display of text above the leader stub.
This option applies to Labels.
It also applies to radial type dimensions (radius, diameter, hole,
concentric circle, folded radius) when the Text Alignment is Horizontal
or By Angle. Currently, only options UF_DRF_NO_TEXT_ABOVE_LEADER and
UF_DRF_LEADER_BOTTOM_TEXT_MAX are valid for dimensions.
All options except the first display the text above the leader stub.
Options with 'BOTTOM' display the leader stub below the bottom line of
text. Options with 'TOP' display the leader stub below the top line of
text.
Options with 'UNDERLINE' will underline all other lines of text.
Options with 'MAX' will extend the stub and optional underlines to the
maximum text length. For options without 'MAX' the stub and optional
underlines will be extended to the length of the text line it is under.

UF_DRF_text_arrow_placement_t specifies the type of placement for the
dimension: inferred or manual.

UF_DRF_text_just_t specifies the supported horizontal text justifcation
options

Possible value for text type

UF_DRF_tolerance_location_t specifies the location of the tolerance value
relative to the dimension text

UF_DRF_tolerance_type_t specifies the tolerance type for a dimension

User Defined Symbol pen types

The following enumerated type is used for setting the user defined
symbols parameters on objects and determines whether the stored values
should be interpreted as "length / height" or "scale / aspect ratio"
parameters.

Centerline forms

Area Fill material types

UF_DRF_vertical_text_just_t specifies the supported vertical justification
options

enum declaration for contour type of the weld

enum declaration for type of finish for the weld

enum declaration for identification line response

enum declaration for size code

enum declaration for extension type

enum declarations for the weld symbol types